Cirronet HN 210X Guide de l'utilisateur Page 31
- Page / 52
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
HN-2010
Demonstration Procedure
The procedure below provides a quick demonstration of the WIT241x.
1. Attach a transceiver to each computer, preferably between 5' and 30' apart for
convenience.
2. Start WinCOM running on both computers If you prefer, almost any other serial
communications program such as Procomm or QModem set for 9600 bps will
also work.
3. Turn the radios on and use the function keys to set DTR and RTS to 1 (if you are
using a terminal program other than COM24, these are typically set
automatically). The radio should respond by setting both DSR and CTS to 1, and
transmit a short sign-on message including the firmware version and whether the
unit is configured as a base or remote. Watch the states of the hardware control
lines on the status bar as you do this. The DCD indicator should be lit on the base
station. After a few seconds, the remote unit will acquire the base station's signal
and also assert its DCD signal.
4. Access modem control mode for each unit. To access modem control mode, use
the F1 key to toggle DTR to 0 and back to 1 and then press the F3 key, which
sends the ":wit2400" escape sequence. If you are not using COM24, simply turn
the radio off and back on and then type ":wit2400" (must be lower case, no
backspace characters). The transceiver should echo back “
>” to indicate that you
have entered modem control mode. Check the remote unit's hopping pattern by
entering "wn?" at the prompt. The remote should respond with "0", the default
setting. Check that the base station's hopping pattern matches this by entering
"wn?" at the base station.
5. Exit control mode by entering "z>". Do this for both radios. At this point, you
should be able to type characters into either radio and see them appear at the other
side. If you are using WinCOM, you can press the F6 key to transmit a repeating
test pattern.
6. For a range test, disconnect the remote station from the computer and power
supply. The DCD indicator should remain lit as long as the base station is in
range..
7. Exit COM24 by pressing the ESC key.
© 2000- 2004 Cirronet™ Inc 25 M-2410-0011 Rev B
- HN-2010 1
- User’s Guide 1
- Declaration of Conformity 3
- Table of Contents 4
- Overview 7
- Design Features 8
- Glossary of Terms 9
- About HopNet Products 10
- HN-2010 Repeater 11
- RF Antenna Connectors 12
- Conxall Power Connector 12
- DB-9 Connector 13
- Three-Way Switch 13
- LED Status 14
- Antenna Connectors 15
- Configuring the Repeater 16
- Technical Specifications 17
- Mechanical 18
- Environmental 18
- Configuring the Network 19
- Starting the program 22
- Function Keys 25
- WinCom Tools 26
- Script Commands 28
- Demonstration Procedure 31
- Modem Commands 32
- Serial Commands 32
- Set Data Rate Divisor 33
- Set Protocol Mode 33
- Network Commands 34
- Enable Global Network Mode 35
- Set Hopping Pattern 35
- Set Transmit Power 35
- Set Range Optimization 36
- Protocol Commands 37
- Set Hop Duration 38
- Set Minimum Data Length 38
- Set Packet Attempts Limit 39
- Set Data Transmit Delay 39
- Set ARQ Mode 40
- Status Commands 41
- Set Duty Cycle 42
- Memory Commands 43
- Modem Command Summary 44
- Guidelines for Installation 45
- Typical HopNet Applications 46
- Troubleshooting 47
- Common System Problems 48
- Introduction 49
- Customer Support 51
- Warranty 52
Produits connexes et manuels pour Mise en réseau Cirronet HN 210X
(2 pages)Campbell manuali
La lista Campbell dei dispositivi contiene 340 manuali utenti e le guide per 168 modelli in 34 tipi di dispositivo
-
Mobili per bambini -
Fotocamere bridge -
Tester per rete -
Accessori per fotocamera -
Caricatori di batterie per auto -
lettori di tessere -
Componenti del telaio auto -
Pianoforti digitali -
Contenitori elettrici -
Accessori per pannelli piani -
Misurazione, test & controllo -
Telefonini -
Accessori per motocicli -
Navigatori -
Switch di rete -
Networking -
Macchina per riduzione rumore -
Equipaggiamento per l’ossigeno -
Tavolini per PC/Workstation -
Cura degli animali -
Prolunghe -
Alimentatori -
Telecamere di sicurezza -
Componenti per dispositivi di sicurezza -
Server -
Software -
Stufette -
Antenne TV -
Televisori e monitor -
Convertitori video -
Regolatori di voltaggio -
Stazioni metereologiche -
no
Commentaires sur ces manuels