Cirronet SEM2410 Guide de l'utilisateur

SEM2410 /X /D /DX Wireless Ethernet Bridge User’s Guide 3079 Premiere Pkwy Ste 140 Duluth, Georgia 30097 www.cirronet.com (678) 68

SEM2410 SEM2410X/DX Figures 4, 5 & 6 show the connectors and LEDs on the SEM2410X & SEM2410DX radios. Figure 7 illustrates the remote radio as

SEM2410 Figure 6. SEM2410DX Front Panel Diagram Figure 7. Remote Radio Assembly © 2000- 2005 Cirronet™ Inc 6 M-2410-0018 Rev C

SEM2410 The remote radio assembly has mounting holes to secure the antenna. The antenna is attached to the remote radio through the included 24-inch R

SEM2410 Complete the assembly by placing the connector in the slot in one of the shell halves. Install the two retaining screws on both sides of the s

SEM2410 CONNECTOR PIN CONDUCTOR COLOR CONNECTOR PIN CONDUCTOR COLOR 1 Brown 9 Green 2 Orange/Black 10 Orange 3 Black 11 Violet 4 Blue 12 Yellow 5

SEM2410 The power connector is a 2-pin DIN type connector. The provided AC adapter provides a 12 volt power level to the SEM. The SEM2410 and SEM2410D

SEM2410 Configuring the SEM The network that the SEM is connected to must be compatible with 10/100BaseT products. Before connecting a default configu

SEM2410 Open IP Hunter by double-clicking on the file iphunter.exe on the SEM2410 CD. The following screen will appear. Click on the Search button t

SEM2410 Double-clicking on a device with an IP address of 0.0.0.0 will bring up the following dialog box. Enter the desired IP address and the defaul

SEM2410 HTML Setup Once an address has been assigned, double-click on the IP number to launch an HTML setup session in a browser window. The login scr

Important Regulatory Information Cirronet Product FCC ID: HSW-2410 IC 4492A-2410 Note: This unit has been tested and found to comply with t

SEM2410 System Settings This dialog allows the user to change the Hostname, set the Default Route, enter DNS entries or change the Outmax (upload/d

SEM2410 Bridge Settings This dialog allows the user to set the Mode, (Master or Slave), any Filtering (see the section on Filtering below) and whet

SEM2410 Access Control Users This dialog allows the modification of logins and the ability to add new users. Note: Click on Save Settings to store t

SEM2410 The SEM will report back the time it took to the save the information. Reset the SEM by typing: reset<CR> The SEM can also be reset by

SEM2410 SEM Operation Overview SEM devices are wireless Ethernet modems that perform bridging functions in point-to-point or point-to-multipoint confi

SEM2410 the master automatically configures the radio in the master as a base radio. Similarly, configuring a SEM as a slave automatically configures

SEM2410 If the application has more slave devices, or if it is desirable to increase the throughputs of the slaves at the expense of the master SEM, c

SEM2410 SEM Command Set The SEM supports a series of commands that allow for configuring the Ethernet interface as well as the radio parameters of the

SEM2410 arp Manipulates the address resolution procedure table. This command is provided primarily as a debugging tool for setting up networks. ipadd

SEM2410 Bridge Commands Command Description help Displays help screen for command access <accesscode> Sets access code to allow slave SEM onto

Declaration of Conformity Warning! The RLAN transceiver within this device uses a band of frequencies that are not completely harmonized within the

SEM2410 SEM Security Commands Command Description access help console [enable|disable] ip [help add <ipaddr> delete <ip

SEM2410 Radio Commands Command Description hop [help fcc [enable|disable] length <hoplen> sequence [75|25] set <pattern> (Master only

SEM2410 The parameter entered for length is the decimal value of the number of 625 µsec ticks in the desired dwell time. A value of 24 (decimal) corre

SEM2410 The following commands are issued by typing radio and then the subcommand followed by the subcommand parameters if any. Command Description he

SEM2410 more than maxslaves slave SEMs attempt to connect to the access point, they will be denied access. network The radio in the SEM has 64 prep

SEM2410 Specifications Model SEM2410 SEM2410X SEM2410D SEM2410DX Data Throughput 200Kbps full duplex point to point Total over-the-air bandwidth 460.8

SEM2410 Troubleshooting Ethernet Link LED is not on. Check the power LED on the SEM. Check the Ethernet cable, making sure that it is fully connect

SEM2410 Warranty Seller warrants solely to Buyer that the goods delivered hereunder shall be free from defects in materials and workmanship, when give

WARNING!! ≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡ For our Customers who wish to use this product in hazardous locations. This SEM2410D/X/DX has

Table of Contents Introduction ...

SEM2410 Introduction The SEM2410 family of products from Cirronet™ Incorporated provides wireless Ethernet connectivity between networks located more

SEM2410 Getting Started The SEM family of wireless Ethernet modems is easy to install and operate. In most instances, the only installation steps will

SEM2410 SEM2410, SEM2410D Figures 1, 2 & 3 show the various connectors and LEDs on the SEM2410 and SEM2410D. Figure 1. SEM2410 Front Panel Diagr

SEM2410 Connectors The RF connection on the SEM is the antenna on the top of the SEM2410D. The antenna connector is a reverse-TNC male type connector